We’re ALTEN Technology USA, an engineering company helping clients bring groundbreaking ideas to life—from advancing space exploration and life-saving medical devices to building autonomous electric vehicles. With 3,000+ experts across North America, we partner with leading companies in aerospace, medical devices, robotics, automotive, commercial vehicles, EVs, rail, and more.
As part of the global ALTEN Group—57,000+ engineers in 30 countries—we deliver across the entire product development cycle, from consulting to full project outsourcing.
When you join ALTEN Technology USA, you’ll collaborate on some of the world’s toughest engineering challenges, supported by mentorship, career growth opportunities, and comprehensive benefits. We take pride in fostering a culture where employees feel valued, supported, and inspired to grow.
Workplace: On-site, Monday-Thursday. Fully REMOTE on Friday.
Location: Long Beach, CA
Salary: $115-130k
Support design verification and production validation of a high voltage zonal control module through vehicle launch. The engineer works hands on in the client's HV lab executing component, board and module level test campaigns, building the automated setups that run them, and turning raw data into failure analysis the design team can act on.
High temperature validation is complete and low temperature validation is underway, with a parallel design revision in progress. This is an execution role with a high degree of autonomy. The engineer receives the product overview and the objective, then defines the approach, builds the setup, runs the campaign and delivers the result. Technical support is available when something is genuinely blocked, but day to day direction is not.
Responsibilities
• Execute DV and PV test campaigns on high voltage zonal module hardware, including relay life cycle testing to defined cycle counts, low temperature validation and environmental stress testing.
• Build and operate bench setups using oscilloscopes, DMMs, programmable power supplies, power amplifiers, electronic loads and signal generators.
• Write Python automation to drive instrumentation and sweep test parameters, for example voltage sweeps across a 36V to 54V range and frequency sweeps, rather than manual adjustment.
• Perform component and board level characterization: buck and boost converter validation, SPI bus characterization, high side driver characterization under representative capacitive loading, and repeat run characterization across 100 plus iterations to surface intermittent failures.
• Capture and reduce test data, run first pass failure investigation, and hand findings to the responsible design engineer with a clear recommendation.
• Author and maintain test plans, procedures and reports, and report task level progress on a near daily cadence.
• Work from the product specification to determine what needs to be tested and how, with minimal direction.
Required Qualifications
• Bachelor's in Electrical Engineering, Computer Engineering or a related field.
• 3 to 7 years in hardware test, validation or bring up, ideally on automotive or power electronics hardware.
• Demonstrated hands on bench skill: oscilloscope, DMM, power supply, electronic load, probing and instrumentation setup.
• Python for test automation and instrument control (pyvisa or equivalent).
• Component and board level debug ability. Comfortable reading schematics and datasheets.
• Self directed. Able to take an objective and define the test approach without supervision.
• Legally authorized to work in the United States.
Preferred Qualifications
• High voltage automotive experience: onboard charger, DC/DC converter, BMS, zonal or body control modules.
• Familiarity with DV and PV processes, DVP&R, and automotive environmental and life cycle test standards.
• CAN and serial bus tooling, HIL exposure.
• Prior work on a prototype to production transition within a vehicle program.
Salary Range
• $115,000 - 130,000
• The actual salary offered is dependent on various factors including, but not limited to, location, the candidate’s combination of job-related knowledge, qualifications, skills, education, training, and experience
All qualified applicants will receive consideration for employment and will not be discriminated against on the basis of race, color, religion, sex, sexual orientation, gender identity, national origin, disability, protected veteran status, age, genetic information, or pregnancy.
Please beware of job seeker scams and see this important notice on our careers page for more information about our recruiting process.
Compliance Notice: Alten USA is a federal contractor subject to the requirements of the Vietnam Era Veterans’ Readjustment Assistance Act (VEVRAA) and Executive Order 11246. We are an Equal Opportunity Employer and consider all qualified applicants without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, disability, or veteran status.
Drug Screening Requirement: As a federal contractor, Alten USA maintains a drug-free workplace. All candidates selected for employment will be required to successfully complete a pre-employment drug screening as a condition of hire.
Skills Required
- Bachelor's degree in Electrical Engineering, Computer Engineering, or a related field
- 3 to 7 years of experience in hardware test, validation, or bring-up, ideally involving automotive or power electronics hardware
- Hands-on bench testing experience with oscilloscopes, DMMs, power supplies, electronic loads, probing, and instrumentation setup
- Python experience for test automation and instrument control, using PyVISA or an equivalent
- Component- and board-level debugging skills, including the ability to read schematics and datasheets
- Ability to work independently and define test approaches without supervision
- Legal authorization to work in the United States
- High-voltage automotive experience with onboard chargers, DC/DC converters, BMS, zonal modules, or body control modules
- Familiarity with DV and PV processes, DVP&R, and automotive environmental and lifecycle test standards
- Experience with CAN and serial bus tooling or HIL systems
- Experience transitioning prototypes to production within a vehicle program
What We Do
ALTEN Technology USA is an engineering consulting company that provides innovative solutions for engineering, IT, and product development projects across the product life cycle. For decades, ALTEN Technology USA has been helping clients develop products that are changing the world, whether by shaping the future of space exploration, saving lives with medical devices that set new standards of care or creating the fully autonomous electric taxi of tomorrow. The company provides support across industries including aerospace, defense, MedTech and life sciences, unmanned systems and robotics, automotive OEM and tier 1 suppliers, commercial vehicles, electric vehicles, energy and environment, rail, and more.
Why Work With Us
Potential clients in the industries we serve, Professionals in the Industries, and Potential employees within New Product Development, Engineering Services, Sustaining Engineering, Manufacturing Engineering, Embedded Electronics Engineering, Software Engineering and IT, Mechanical Engineering, and Systems Engineering.
